Installation guide

Installation technical guidance
1.firstly, installation staff should know the craft of products, overall construction; all hardware’s function and feature.

2.Installation work should start with find all necessary parts, figure out the way to install the products(what install firstly, what next, etc.).Check all parts quantity and quality. Pay attention to protect products during installation: Get and place the parts softly, do not kick or pull by hand if installation process not going well. Using rubber hammer to fix wood plugs and plastic buttons softly ,in case damage surface of furniture or imprint of hammer. When install glass and mirrors, pay attention to carefully hold, do not break them.Install frosted glass, the frosted side should face inside. Door gasket and drawer sliders should adjust to suitable position then fasten. Drawer slider must fix at least 3 pcs screws.

Common problems and the way to deal with them during installation:
1）gap between Cabinet and doors not even,should be adjustable to even by adjust the door hing( this requires installation workers know door hinges fuction and feature very well)
2）Gap between drawer box and drawer front panel not even.
if gap uneven is left and right –horizontal , can put slice of wood or other material at side of drawer slider(between drawer slider and side panel of cabinet ) to adjust ,put it at the side which gap is bigger.
If gap uneven is up and down ,then should adjust by adjusting the height position of drawer slider.
3）Panel loose: back panel’s looseness will lead to unstable of the whole furniture’s construction. Looseness of back panel are lead by following reasons:
3．1．The groove to Install back panel is too deep.
3．2．Back panels size too small to fit.
Above two situations can be solved by put slice into the groove at back.Please handle this issue depends on actual situation.

1）solution of Fixing Furniture notch, scratch, holes deviation .
Firslty, clean up the separate layer lacquer and burr around notch, scratch.  Use similar color epoxy putty    to fill the notch according to the actual notch’s space, scratch’s depth. Use hand to knead the putty even and fill the notch or gap within 3 minutes( about 4-7 minutes after it solidification and dry), use wallpaper cutter to scrape the extra epoxy putty which is higher than level, use 320#sand paper to polish surface. Use bottle transparent primer spray, keep the distance about 100-150mm.Do not spray too much one time, in case of whitish (takes about 5-10 minutes time to dry). Use 400#sand paper to polish the sand grain of 320#sand paper. Select similar color powder or painting oil brush to stain color. When stain color, add color slowly layer by layer, quality should be same as products color finish. Then start top coating spray(5-10 minutes). Use similar color and grain pen to draw follow the original surface grain. Then use 600# sand paper to clean dust. Select same degree shine lacquer to make top coating spray.  

2)solution of Fixing Furniture notch, scratch, holes deviation .
1.Products are open lacquer painting, top lacquer thin, easily affect by damp and climate change, crack, what’s more, there maybe damage during transportation and caring, should use iron clamp to adjust correct and fix during repairing, under the situation that not affect normal using, can use filling method to fix.

2.When the notch ,scratch are very small, use rod wax( many types) to repair. Use electronic iron knife  to melt the wax, Be careful when operating, avoid the electronic iron knife burn furniture, or make furniture fading. Smear the melted wax around the notch,scratch, after it become smooth and plain(takes 2-3 minutes to dry),scrape off the extra wax and clean up the surface. Use similar color to touch up the surface slowly layer by layers, from light to dark color till the color is consistent. Then use steel wool to clean up dust then spray top coating.

3.When the notch is big, use similar color epoxy putty to fill the notch according to the actual notch’s space, scratch’s depth. Use hand to knead the putty even and fill the notch or gap within 3 minutes( about 4-7 minutes, after it solidification and dry), use wallpaper cutter to scrape the extra epoxy putty which is higher than level, use 320#sand paper to polish surface. Use bottle transparent primer spray.(takes about 5-10 minutes time to dry). Select similar color powder or painting oil brush to stain color.Then start top coating spray (takes about 5-10 minutes time to dry ). Use similar color and grain pen to draw follow the original surface grain, not too deep, should keep consistent with original grain. If close painting ,no need to carve the grain. Then use steel wool to clean up dust then spray top coating.

3)solution of fixing Furniture loose. 
1.Put adhesive for wood splice into the gap, use iron clamp tight clip (about 2-4 hours will dry) . Meanwhile,use ferrous glue(about 30-60 minutes will dry), make the detail position’s repair ,use wallpaper cutter to scrape the extra glue. Use similar color oil painting pen or brush to touch up the white line. Spray primer coat (takes 5-10 minutes to dry), use 320# sand paper to polish smoothly, then spray top coating.
What’s more: clean up the loose sundries, put the strong adhesive glue fix, spray whitish resistant catalyst ,about 2-3 minutes ,it will dry, then use sand paper to polish and touch up color ,then spray top coating.  

4)Fix the color difference of furniture.
1.The reason of color difference is during the production procedure, color control not very well ,another reason is affected by air and humidity ,lead to discoloration and fading.
2.Match color. Firstly analyze the products basic color are composite by which colors.
3.Mixing materials ,such as: thinner, Isophorone , alcohol ,  add red, yellow, black ,white color concentrate.
4.Before putting on color: 1) separate the color required. 2) white cotton cloth 3 pcs, L40*D30mm; one cloth wet by color painting oil, one cloth wet by Isophorone, another cloth prepared to clean extra color and dust.
5.When putting on color: follow the wood veneer ‘s grain direction equally brush surface back and forth until the color consistent. After that, clean up the variedness color, there will be slightly foggy ,it will vanish after several minutes.